HT12E DATASHEET IN PDF

The capability to select a TE trigger on the HT12E or a DATA trigger on the HT12A further enhances the application flexibility of the 2 12 series of encoders. HT12E Datasheet, HT12E Holtek Encoder Datasheet, buy HT12E Encoder IC. The capa- bility to select a TE trigger on the HT12E or a. DATA trigger on the HT12A/B/C further en- hances the application flexibility of the 2.

Author: Akinogar Daikasa
Country: Great Britain
Language: English (Spanish)
Genre: Sex
Published (Last): 4 November 2013
Pages: 49
PDF File Size: 8.29 Mb
ePub File Size: 9.59 Mb
ISBN: 606-8-25172-771-2
Downloads: 64558
Price: Free* [*Free Regsitration Required]
Uploader: Zulkishicage

These 12 bits are divided into 8 address bits and 4 data bits. SPI Module of Arduino. If you want security you can connect any of the 8 pins to 5V to make it high.

So out of the bits 8-bits will be used to set address and the remaining 4-bit will be used datashert transmit data.

The primary function of HT12E is to encode a bit and send it out through the output pin. HT12E begins a 4-word transmission cycle upon receipt of a transmission enable. This data should be sent to the HT12D for decoding, it can either be sent directly through a wire or by using a wireless medium like RF or IR.

The IC has a built in oscillator. HT12E is an encoder integrated circuit of 2 12 series of encoders. Submitted by admin on ht122e October What is Web Browser.

They can also be connected to switches to manually send and receive data. This pin has to be connected to Ground 0V to enable the Transmission. The Encoded 12 bit output data can be obtained from this pin.

  CARNALLY EVER AFTER JACKIE BARBOSA PDF

Virgin Galactic — Commercial Space Flight. As soon as TE returns to high, the encoder output completes its final cycle and then stops. Transmission enable; active low. Connected to the Ground of circuit. Choosing Motor For Robots. Choosing Battery for Robots. These are the 8-bit address bits, which is used to protect your data.

TL — Programmable Reference Voltage.

Interface SD Card with Arduino. This oscillator can be used by connecting these two pins through a 1M Resistor. The 4-bit data that has to be sent has to be given to the pins AD0 to AD1 and an address of 8-bit has to be set using the pins A0 to A7. Interface GPS with Arduino. Supply voltage; 5V 2. These four pins are used to send data, the data encoded here will be decoded on HT12D IC sharing the same address bits. It is mainly used in interfacing RF and infrared circuits. The IC is has a wide range of operating voltage from 2.

The encoded bit can be obtained from the Dout pin pin In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground.

HT12E Encoder IC Pin Diagram, Uses, Equivalents & Datasheet

So if you are working on a project which has to transmit a 4-bit data from one end to other either by wire or wireless then this IC pair will be best suited for you. Simply put, HT12E converts the parallel inputs into serial output. Skip to main content. Can range from 2. A basic connection diagram for the HT12E IC is shown below In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground.

  CHFI SYLLABUS PDF

These two ICs together form an Encoder and Decoder pair. This cycle is repeated as long as TE is kept low. It encodes the 12 bit parallel data into serial for transmission through an RF transmitter. You can know to set up the HT12D after this from here. For decoding a data the IC will requires an oscillator, luckily this IC has one in-built. HT12E has a transmission enable pin which is active low.

Arduino based GPS receiver. They are paired with 2 12 series of decoders for use in remote control system applications. In this image I have made all four data bits as zero lowwhen this is decoded we will get the same kind of bits on the output side of HT12D, similarly we can make any changes on these 4-bits and they will be reflected on the output side of the HT12D decoder IC.

HT12E Encoder IC

Can be used in Home automation for short range remote switching Safety systems like Burglar alarm system, Smoke or Hht12e alarm system etc.

This high-density System-in-Package SiP integrates controller, power switches, and support components. We should set the bits in same pattern on Encoder and Decoder IC to pair them. It is very important that your Decoder should also have this same address for them to talk to each other. Pull the Transmission Enable pin pin 14 to ht12 to activate transmission.