ASTM E1300 PDF

New Provisions in ASTM e‐ A comparison of the Basic and New Analytical Procedures for Determining the. Load Resistance of. ASTM E Standard Practice for Determining Load Resistance of Glass in Buildings Book of Standards Volume American Society for. ASTM E is the main source of technical information for architects and other design professionals to determine the right glass thickness and type to meet a.

Author: Shak Bazuru
Country: Dominican Republic
Language: English (Spanish)
Genre: Automotive
Published (Last): 22 June 2007
Pages: 223
PDF File Size: 8.41 Mb
ePub File Size: 5.39 Mb
ISBN: 467-9-61099-422-9
Downloads: 72477
Price: Free* [*Free Regsitration Required]
Uploader: Merisar

IGUs reduce sound transmission and provide quieter interior spaces. The thermal barrier makes interior spaces more comfortable as it is easier to maintain a consistent indoor environment.

This practice assumes that the edges of the glass are simply supported and free to slip in plane. The number of glass edges supported.

If you see condensation on the outside of e300 low-e glass windows, it means the coating is working properly. The values given in parentheses are for information only. Designing Glass to Resist Wind and Snow Loads Accommodating for wind and snow is one of the important upfront considerations r1300 the design and specification process.

The glass type factor, which is the multiplying factor for adjusting the load resistance of different glass types. However, some applications can be two-sided support, such as Butt Joint Glazing or sometimes even three-sided or one-sided supports.

The surface condition of the glass doesn’t have any significant damage. Monolithic, laminated and insulating glass constructions made with annealed or heat-treated glass.

The procedures operate under some basic assumptions related to glass fabrication and installation, including: This practice assumes that 1 the supported glass edges for two, three, and four-sided support conditions are simply supported and free to slip in plane; 2 glass supported on two sides acts as a simply supported beam; and 3 glass supported on one side acts as a cantilever.

  9TH BIPARTITE SETTLEMENT FOR BANK OFFICERS PDF

Resist Wind & Snow Loads | Vitro Glass Education Center

D Practice for Plastics: The final thickness and type of glass selected also depends upon a variety of other factors see 5. The relative strength of glass for a given thickness, width, height and number of supported edges. Glass 6mm thick will weigh 2. Typically all four sides are supported in a framed e3100 or a four-sided Structural Silicone Glazing.

About The Education Center Resources.

This practice does not apply to glass with surface or edge treatments that reduce the glass strength. Due to the chemistry involved in the float glass process, all the colors of the rainbow are not possible.

The final thickness and type of glass selected also depends upon a variety of other factors see 5. The values given in parentheses are for mathematical conversions to inch-pound units that are provided for information only and are not considered standard. This practice shall not apply to other applications including, but not limited to, balustrades, glass floor panels, aquariums, structural glass members, and glass shelves.

Active view current version of standard.

Determination and Report of Procedures. There is a multi-step process that must be undertaken to 1e300 ensure the glass in your project is able to resist these loads.

Astm e 1300

The assumptions and calculations result in these basic design procedures that should be followed:. For example, orange, red, yellow and violet colored glasses cannot be produced using standard float technology.

A procedure is also presented to calculate the probability of breakage of any annealed lite or ply see Appendix X3for short or long duration loads. Glass Education Center The single source for information on designing, specifying and building with commercial glass. For conversion of quantities in various systems of measurements to SI units, refer to SI Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

  DELPHI SHELLEXECUTE PRINT PDF

Designing Glass to Resist Wind and Snow Loads

This practice assumes that 1 xstm supported glass edges for two, three, and four-sided support conditions are simply supported and free to slip in plane; 2 glass supported on two sides acts as a simply supported beam; and 3 glass supported on one side acts as a cantilever. Work Item s – proposed revisions of this standard. This practice does not consider the effects of deflection on insulating glass unit seal performance.

It also weighs the same. Glass deflections are to be reviewed. How much does glass weigh? This practice shall not apply to other applications including, but not limited to, balustrades, glass floor panels, aquariums, structural glass members, and glass shelves.

ASTM E – 09 Standard Practice for Determining Load Resistance of Glass in Buildings

For insulating glass units, this practice only applies to insulating glass units with four-sided edge support. D Practice for Plastics: Link to Active This link will always route to the current Active version of the standard.

Basic Design Procedures The assumptions and calculations result in these basic design procedures that should be followed: IGUs reduce the likelihood of interior condensation forming by providing a thermal barrier between the inside and the outside.